designed & dimensioned in millimeters[inches] this product manufactured with lead-free processing pb do not scale from this print rf058-xxxxx-xxxxxx-xxxx overall cable length millimeters of cable 0100 min. (see note 8 & 9) end 1 connector end 2 plating option -05sr: tnc-p-c-xx-sr-c10 (see sheet 2) -06sp: ntpe-p-c-xx-st-c10 (see sheet 2) -01bj: sma-j-c-xx-st-b10 (see sheet 2) -01sb: sma-j-c-xx-st-s10 (see sheet 2) -01sp: sma-p-c-xx-st-c10 (see sheet 2) -sing: single ended (one end only, see note 11) -xxxxxx: stripped and tinned (this end only- see notes 11-16 & sheet 2, fig. 3) (see fig. 2) "c" format: x.x mm (see fig. 2) "b" format: x.x mm (see fig. 2) "a" format: x.x mm -05sr: tnc-p-c-xx-sr-c10 (see sheet 2) -06sp: ntpe-p-c-xx-st-c10 (see sheet 2) -01bj: sma-j-c-xx-st-b10 (see sheet 2) -01sb: sma-j-c-xx-st-s10 (see sheet 2) -01sp: sma-p-c-xx-st-c10 (see sheet 2) 1: gold all components 2: gold/nickel 3: alternate gold / nickel 7. alternate gold medium/ gold flash (see sheet 2 for plating specifics) (leave blank for -sing or -xxxxxx end 2 preparation) 058: cca-058 (rg-58 coaxial cable) cable callout do not leave any space blank, each must contain a numeric character 0 thru 9. end 1 plating option end 2 connector or preparation l l l * * * * * * (* = not released for production) l 1: gold all components 2: gold/nickel 3: alternate gold / nickel 7. alternate gold medium/ gold flash (see sheet 2 for plating specifics) l "a" mm "b" mm "c" mm "d" mm "e" mm fig.2 cable stripping dimensions per configurations (see table 1)(see notes 12,13,14,15) c c c c c c fig.1 rf058-05srx-06spx-xxxx shown c sheet of unless otherwise specified, dimensions are in millimeters [inches]. tolerances are: decimals angles .x: 0.3 [.01] 2 .xx: 0.13 [.005] .xxx: 0.051 [.0020] material: rf058 cable assembly by: rf058-xxxxx-xxxxxx-xxxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing tim p. 5/6/2005 2 1 sheet scale: 2:1 see end 1 and end 2 assembly prints f:\dwg\misc\mktg\rf058-xxxxx-xxxxxx-xxxx-mkt.slddrw notes: 1. represents a critical dimension 2. cable cut length: = (length: xxxx) - (subtractor for end 1) - (subtractor for end 2). (see table 1 for subtractors) 3. assembly to be 100% tested for opens & shorts 4. assembly to be 100% hi-pot tested per table 1 5. after final electrical tests, label each cable assembly with 1 label -et 6. criticals on connector prints to be checked in process 7. finished assemblies to be packaged per packaging standard co-hd-wi-3033-m. 8. cable stocked in inches, 1 inch = 25.4 millimeters 9. cable lengths longer than 1000 millimeters are not supported by s.i. test data 10. minimum bend radius for rg058 = 48.3 [1.90] 11. for sing ended or stripped and tinned assemblies: make a double ended assembly at twice the cable length and test before cutting assembly in half. 12. dim "a", "b", and "c" have a minimum value of 0.0mm & a maximum value of 9.9mm 13. production of strip and tin for center dielectic use: a 14. production of strip and tin for shield use: d=a+b 15. production of strip and tin for jacket use: e=a+b+c 16. for stripped and tinned option, only the center conductor is tinned 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision l
-05sr (straight plug) (use drawing no. tnc-p-c-xx-sr-c10 for assembly instructions) -06sp (straight plug) (use drawing no. ntpe-p-c-xx-st-c10 for assembly instructions) fig.3 rf058-05srx-102148-xxxx shown plating options 2: 30" min. gold center contact 100" min. nickel outer contact 100" min. nickel remaining metal parts (end connector p/n: ntpe-p-c-hn-st-c10) 3: 10" min. gold center contact 100" min. nickel outer contact 100" min. nickel remaining metal parts (end connector p/n: ntpe-p-c-gn-st-c10) note: all critical dimensions on ntpe-p-c-xx-st-c10 that apply must be verified. *-01bj (straight bulkhead jack) (use drawing no. sma-j-c-xx-st-b10 for assembly instructions) plating options 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-j-c-h-st-b10) 7: 10" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-j-c-gf-st-b10) note: all critical dimensions on sma-j-c-xx-st-b10 that apply must be verified. plating options 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-j-c-h-st-s10) 7: 10" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-j-c-gf-st-s10) note: all critical dimensions on sma-j-c-xx-st-s10 that apply must be verified. *-01sb (sealed straight bulkhead jack) (use drawing no. sma-j-c-xx-st-s10 for assembly instructions) *-01sp (straight plug) (use drawing no. sma-p-c-xx-st-c10 for assembly instructions) plating options 1: 30" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-p-c-h-st-c10) 7: 10" min. gold center contact 3" min. gold outer contact 3" min. gold remaining metal parts (end connector p/n: sma-p-c-gf-st-c10) note: all critical dimensions on sma-p-c-xx-st-c10 that apply must be verified. l l l plating option 3: 10" min. gold center contact 100" min. nickel outer contact 100" min. nickel remaining metal parts (end connector p/n: tnc-p-c-gn-sr-c10) note: all critical dimensions on tnc-p-c-xx-sr-c10 that apply must be verified. sheet of rf058 cable assembly by: rf058-xxxxx-xxxxxx-xxxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing tim p. 5/6/2005 2 2 sheet scale: 1:1 revision l f:\dwg\misc\mktg\rf058-xxxxx-xxxxxx-xxxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
|
